DIMENSIONS

• 3.25 IN (H) X 7 IN (W) X 1.125 IN (D)
• 8.26 CM (H) X 17.78 CM (W) X 2.86 CM (D)

WEIGHT

• 13.5 oz/385 g
• With optional mounting bracket 40.57 oz. (1150 g)

OPERATING TEMPERATURE

• -40? to +85? C

INPUT VOLTAGE

• 10 TO 48 VDC

BATTERY TYPE

• Built-in rechargeable NiMH batteries (non-replaceable)

CERTIFICATIONS & STANDARDS

• FCC, ISED, CE, AUS/NZ, ANATEL, INMETRO CERTIFICATE â???? LMP 19.0127 X
• PENDING: JQA(JAPAN), IFT, INDONESIA
• ATEX/IECEx II 1 G,Ex ia IIC T4 Ga For international Zone 0 applications, HERO
• North America cETLus:
  â???? Class I, Division 1, Groups A-D, T4. â???? Class I, Zone 0, AEx ia IIC T4 Ga
• WEEE Compliant
• GMPCS-MoU
• IP68/69K, MIL-STD-810G for: Immersion, Impact resistance, Salt Fog, Acidic Atmosphere, Humidity Vibration

• 12 different reporting times
• Interval or 24-hour operation mode
• Alternate reporting schedules
• Low battery message
• Motion Sensor/Vibration parameter and scheduling
• Contact closure parameters
• Diagnostic messages
• Include Speed and Heading data in reported motion messages

• DIMENSIONS
  • 2.7 x 3.25 x 1in (6.86 x 8.26 x 2.54cm) with brackets
• WEIGHT
  • 3.6 oz (102g) with 4 batteries and mounting hardware
• OPERATING TEMPERATURE
  • -22 to 140?F (-30 to 60?C)
• NOTE: The unit shall remain operational over the -40 to 185?F (-40 to 85?C) range, though may experience battery life and RF signal degradation.
• LINE POWER
  • 5V DC or 8-22V DC with regulator cable
• BATTERY TYPE
  • 4 AAA 1.5V lithium (provides 1.5+ years of life)
• CERTIFICATIONS: ANATEL Certification for Brazil (pending), FCC CFR Parts 15 and 25, Industry Canada, CE Mark (European Certification) and COFETEL
• STANDARDS: SAE J1455 MIL STD 810, NEMA 4X/IP68, RoHS Compliant
• SATELLITE TECHNOLOGY: Global LEO Satellite operation using the Globalstar Simplex Data Network

SmartOne Solar Satellite Tracking User Guide v1.2.1Confidential & Proprietary Information Usage Example: A Company is required to report the GPS locations of their hazardous chemical containers twice a day. Based on this requirement, the Company has two options: set a message interval of every 12 hours, the 12 hour internal begins when the device is powered up or when the configure message times of day are 12:00 noon and 12:00 midnight.Reduced Messaging Reduced Messaging Mode reduces the cost associated with transmitting messages over Globalstar’s satellite network by sending messages at a minimal message interval when the asset is in a defined area and transmits at a higher message interval when the asset is changing locations. These message intervals are set as part of the configuration process based on the concept that repeated reporting information of the same location, when an asset has not moved from its defined area, is redundant and doesn’t provide addition usable information about its current location. By comparing current and prior position information, the SmartOne determines if its location is changing. The definable area in which the device should remain in Reduced Messaging Mode is called the Change of Location Area and it is a square. When the SmartOne goes outside of the square, its location is considered to be changing or relocating.

Usage Example: A fleet operator owns 1,000 trailers. When the trailer(s) are sitting at a depot they want a location message once a day. They also want a message notification within one hour when a trailer has left a depot. Lastly, they want a location message every three hours when a trailer is moving between depots. Based on this requirement, the fleet operator will need to set the Change of Location Area (size of the depots where the trailers will visit), the message interval while the trailers are inside the Change of Location Area (one per day), the interval at which the SmartOne will check its location while in a State of Vibration and inside the Change of Location Area(one per hour), set the number of messages when the trailer leaves the Change of Location Area (one Change of Location Area Alert Message) and the message interval while the trailers are in transit between depots (every three hours).

When the SmartOne is configured to operate in the Theft Recovery Mode, it differentiates between authorized and unauthorized movement of an asset. While the power to the SmartOne is turned off, all movement of the asset is considered authorized. When power is turned on, the SmartOne obtains a position from GPS satellites. The position is used to set the center of the defined Change of Location Area in Theft Alert Mode. While in the Change of Location Area, the SmartOne obtains position fixes at an interval set during configuration. If the SmartOne remains within the Change of Location Area, all movement is considered to be authorized.

Once the SmartOne’s position is outside of the Change of Location Area, it alerts the SmartOne to an unauthorized movement and immediately sends a location message (Change of Location Alert Message). The SmartOne continues to send location messages at a message interval set during the configuration process until the power is turned off or the battery is dead. Usage

Example: A construction company is working on a job site for one year and wants to ensure that their generators and other heavy equipment on site aren’t stolen. The company wants to check the location of their equipment 12 times a day, every 2 hours, to confirm the asset hasn’t been stolen, but only wants a transmitted location message once per day. Based on this requirement, the construction company will need to set the Change of Location Area (size of the job site), the message interval while inside the Change of Location Area (one per day), the interval at which the SmartOnewill check its location while in a State of Vibration and within the Change of Location Area (every twohours) and the message interval if the asset is outside the Change of Location Area.